Buyer guide · By MSdean
A380 Aluminum Alloy: Composition, Properties and Applications
A380 aluminum alloy is an aluminum-silicon-copper casting alloy widely used for general-purpose die-cast components. It combines useful casting characteristics with properties suited to many housings, brackets and equipment parts. Choosing it still requires a review of the finished component: its loads, environment, machining, surface finish and acceptance requirements.
For buyers, the important question is whether the specified grade and manufacturing route meet the application. A material name alone does not define the performance of an assembled product.
What is A380 aluminum alloy?
A380 is commonly discussed in the context of aluminum high-pressure die casting. NADCA identifies A380.0 as a widely used general-purpose alloy and notes its combination of material properties and ease of production. It also explains that other alloys may be preferable when particular casting or performance requirements take priority. [2]
Specify the complete designation. The Aluminum Association distinguishes xxx.0 castings from xxx.1 and xxx.2 ingot. Thus, A380.0 identifies a casting composition; an ingot listing for A380.1 or A380.2 describes a different material form with its own composition limits. An ingot supplier’s data should not automatically become the acceptance specification for the finished casting. [1]
A380 aluminum composition and grade identification
The following values summarize the registered AA A380.0 casting composition in the Aluminum Association’s Pink Sheets, revised August 2025. Values are percentages by mass. Ranges have both lower and upper limits; other numerical values below are maxima. [1]
| Element | Limit (% by mass) |
|---|---|
| Silicon, Si | 7.5–9.5 |
| Copper, Cu | 3.0–4.0 |
| Iron, Fe | 1.3 maximum |
| Manganese, Mn | 0.50 maximum |
| Magnesium, Mg | 0.10 maximum |
| Nickel, Ni | 0.50 maximum |
| Zinc, Zn | 3.0 maximum |
| Tin, Sn | 0.35 maximum |
| Other elements, total | 0.50 maximum |
| Aluminum, Al | Remainder |
Use the complete governing specification and its footnotes for procurement, including any customer-specific restrictions. Agree on the standard edition and evidence of composition before ordering. A certificate should identify the supplied material and relevant batch rather than simply repeat “aluminum alloy.”
Properties that matter in practice
Material selection involves several requirements at once. The table below provides a practical discussion framework for a design review.
| Requirement | What to confirm for the actual part |
|---|---|
| Strength and stiffness | Loads, fastener forces, mounting arrangement and the agreed method of verification. |
| Heat transfer | Heat input, contact surfaces, surrounding components and operating conditions. |
| Corrosion performance | Exposure conditions, mating materials, protective finish and any required testing. |
| Manufacturing suitability | Geometry, casting route, machining allowance and the required final condition. |
NADCA’s property tables distinguish typical material information from guaranteed design values and state how specimens were produced. Read those qualifications with the numbers. A test-bar value is not a promise that every location in a production casting will achieve the same result. [2]
Where a property controls product safety or function, define the required acceptance value, specimen or part location, condition and test method with the responsible engineer. This makes competing quotations easier to compare.
Typical A380 applications
Examples described by alloy producers include electronic equipment chassis, engine brackets, gearbox cases and hand or power tool components. These illustrate the range of general-purpose components associated with A380; they do not establish suitability for every item in those categories. [3]
For an electronics housing, mounting features and assembly access may drive the design review. For a bracket, loading and fastener interfaces may be more important. A component exposed to water, heat or chemicals needs its own assessment, even when a visually similar part already uses the alloy.
Machining and surface finishing
A380 castings may need machining to establish particular bores, threads, flat surfaces or assembly interfaces. State the final dimensions and inspection datums on the drawing, and identify which areas must remain as cast. NADCA describes A380 as having favorable machining characteristics within the aluminum die-casting group. [2]
Review the finish alongside the material and geometry. Possible aluminum casting treatments include coatings, plating and anodizing systems, but each has different preparation and acceptance requirements. [2] Ask the finishing supplier to assess the proposed process on representative parts, particularly when visible appearance matters.
Define cosmetic surfaces, masking, thread protection, color or texture references and inspection conditions. A written finish name is often less useful than an approved sample plus measurable requirements. For sealing or pressure-containing components, also define the applicable leak or pressure test instead of relying on the grade designation.
Is A380 the same as ADC12?
Do not approve a substitution on a name comparison alone. A380 and ADC12 are designations used in different specification systems. Dynacast lists ADC12 separately and discusses it in connection with alternatives for intricate components. [4]
If a supplier proposes another alloy, compare the complete composition limits, required properties, casting behavior and finishing route against the drawing. Record the approved change before manufacture. “Equivalent” should have a defined technical basis.
What to specify when requesting A380 parts
A useful RFQ combines the material requirement with the information needed to manufacture and accept the part:
- Material: complete grade designation, governing standard, edition and permitted substitutions.
- Drawing: controlled revision, 3D model, units and critical dimensions.
- Application: loads, operating environment, assembly interfaces and relevant functional tests.
- Delivery condition: machining, deburring, surface treatment and any assembly work.
- Verification: composition documentation, dimensional checks and agreed sampling requirements.
- Order plan: sample quantity, first production order, expected repeat demand and packaging needs.
When asking MSdean to review a project, include the specified grade and any alternatives your engineering team would consider. Our aluminum die casting capability page explains the manufacturing scope. Send your drawing and requirements to discuss the appropriate material and production route for the part.
Frequently asked questions
What is A380 aluminum used for?
It is associated with general-purpose die-cast parts such as equipment housings, brackets, chassis and tool components. Select it against the actual application and its acceptance criteria.
Does A380.0 mean the same thing as A380.2?
No. In the Aluminum Association system, .0 denotes casting and .1 or .2 denotes ingot. Their registered composition limits differ, so specify the required material form and grade. [1]
Can A380 be machined and coated?
Machining and finishing are possible, but the drawing, surface condition and proposed treatment need a coordinated review. Confirm critical features, cosmetic expectations and finish samples before production.
Can I use a published tensile strength as my acceptance limit?
Not without checking the data’s basis. Typical specimen properties, guaranteed values and results taken from a finished component can serve different purposes. Agree on a suitable requirement and verification method.
Sources
- The Aluminum Association: Pink Sheets, revised August 2025, composition limits and designation system.
- NADCA Product Specification Standards for Die Castings, 2021: Aluminum Alloy Data.
- Belmont Metals: A380.2 Aluminum Alloy, typical application examples.
- Dynacast: Aluminum alloys and applications.
Have a drawing to review?
Share your part requirements, expected quantity and application. Let’s discuss the manufacturing route for your finished component.
Get in touch